Perl_newsxs_flags could not be located in perl58.dll - Page 2

Weldarr · #16 07-01-2009, 12:00 PM

I've ran servers before (within the past 3 months), but just recently decided to start back up. However when I downloaded the rev703 from the project site, I received this perl error upon trying to start up the server. Perl_hv_common_key_len could not be located in the dynamic link library perl58.dll

I thought it might have been related to an outdated perl version, so I removed my version of perl and installed the 8.8.822 version listed here. I've tried restarting/deleting all perl/perl58.dll files and I am still getting this error. Anyone have any insight? Like I said, I have ran servers from this computer before with no problems.

Weldarr · #17 07-03-2009, 10:29 AM

Quote:

Originally Posted by Weldarr

I've ran servers before (within the past 3 months), but just recently decided to start back up. However when I downloaded the rev703 from the project site, I received this perl error upon trying to start up the server. Perl_hv_common_key_len could not be located in the dynamic link library perl58.dll

I thought it might have been related to an outdated perl version, so I removed my version of perl and installed the 8.8.822 version listed here. I've tried restarting/deleting all perl/perl58.dll files and I am still getting this error. Anyone have any insight? Like I said, I have ran servers from this computer before with no problems.

Resolved by updating to 8.8.824

Producer_BMW · #18 07-06-2009, 04:32 PM

My issue still proceeds

I've done the steps correctly and had someone helping make sure I did not fuck it up

and I still the get error on the NEW

AP , Msi :(

Producer_BMW · #19 07-06-2009, 10:42 PM

Bump : please help

mixxit · #20 07-06-2009, 11:22 PM

http://www.eqemulator.net/forums/sho...618#post173618

Producer_BMW · #21 07-06-2009, 11:55 PM

Let me try again :(

anyone with a US : land or cell phone line please help me out ,

Or if you have teamspeak or Vent , I am a verbal learner :(

anyone ? I've tried this like 14 different ways

So_1337 · #22 08-19-2009, 01:27 PM

Just thought I'd pop in to say that this issue was finally resolved on the Windows XP system I'd posted about previously.

Deleting the perl58.dll file out of the Windows/System32 folder is all it took. That's what was screwing things up.

hybrid125 · #23 08-19-2009, 01:35 PM

So what version of perl did you end up using on your xp build?

So_1337 · #24 08-19-2009, 02:21 PM

It was 5.8.8.824. I used the PPM manager to install the DBI-mysql and IO-stringy modules to be sure, but I just uninstalled them to check, and the server loaded just fine.

Just to reiterate:

EQEmu server (build 884 binaries) running on a Windows XP computer using the 5.8.8.824 installation of perl with no additional modification.

Check your windows/system32 folder for the perl58.dll file and make sure to delete it if it is there.

Julesx · #25 10-18-2009, 07:54 AM

I've tried every solution i've found on the forums and i still can't get server to load. Keep getting error..
the procedure entry point Perl_newXS_flags could not be located in the dynamic link library perl58.dll
I've uninstall deleted reinstall removed perl folder removed perldll from system32 folder every idea i've read on posts i've downloaded and installed every version of perl from ActivePerl-5.8.7.813-MSWin32-x86-148120 to ActivePerl-5.10.1.1006-MSWin32-x86-291086 nothing will work. Could it possibly be a Vista issue? I can run start.bat in admistrator mode and i no longer get the perl error but then i get world and eqlaunch.exe error's. I've had my own server up and running before about a year ago on an older comp running xp never seen this error. I've been working on this for 2weeks and i'm finally just completely stumped any new idea would be greatly welcomed. I'm running vista service pack 2.

**Shin Noir** · #26 10-18-2009, 01:05 PM

uninstall perl58 completely, use perl10.
Make sure your paths are accurate. Are you compiling from scratch?

OscarGrouch05 · #27 02-05-2010, 10:10 PM

ActivePerl-5.10.1.1006-MSWin32-x86-291086.msi- i'm going to try running both perl's perl58.dll and perl510.dll don't forget to copy perl5.8.7.exe file and perl58.dll it should work on all clinet's now 80)

if getting that error after following steps above use another verson of 5.8 this does work fine for all client's now. 80) just need one copy of the file in C:\Perl\bin

Step by Step
1. if you have perl installed goto C:\Perl\bin copy and paste perl58.dll and perl5.8.7.exe to another folder
2. remove any version of ActivePerl you have installed
3. installl ActivePerl-5.10.1.1006-MSWin32-x86-291086.msi
4. after done installing copy and paste perl58.dll and perl5.8.7.exe to C:\Perl\bin
5. Done now it'll work on both client's perl58.dll and with perl510.dll

Nimmersatt · #28 05-31-2010, 04:35 PM

tried now for hours, haveing installed 3 different versions of Pearl ... 5.8.8, 5.10 as said in the server setup guid and 5.12. nothing helps at all :-/

Deleted pearl58.dll every single time and Rebooted every single time, i just dont have any clue what i can try else ... guesses are greatly appreciated

thx

Nimmersatt · #29 05-31-2010, 05:33 PM

Ok got it... the problem ist you have to use the EQEMU Version INCLUDING BOTS ... not the other one ... Perl 5.10 works fine with it.

Koshoji · #30 05-13-2011, 02:11 AM

http://www.peqtgc.com/phpBB2/viewtopic.php?t=5264

Here's an updated version of Cavedude's link.