Setting Up A Private Server

[jimbop]

Originally Posted by joligario

With absolutely no idea of how you have things set up, we can only guess. It sounds like you built your server on your localhost and are trying to get people to connect remotely outside your network? If so, perhaps your port forwarding is not set up correctly. Again, we have no idea without any information.

P.S. I hope 5598 was your typo.

Currently, I am only setting it up for myself on my own computer, so yes I am using localhost to set up the server. I checked and double checked again that 5598 is indeed not a typo. I am running Windows 7 Pro 64-bit edition. I have set up my own private server once before on an older computer and had no problems whatsoever, but it was on a very old build on a crashed hard drive so I cannot just go back to that one and update it unfortunately. Also that computer, I used minilogin, so my setup from that one to the current is slightly different.

I guess where to start, I will detail all the steps I have taken. FIrst, I went through all of the steps on the February 2013 version here:

http://www.eqemulator.net/wiki/wikka...rverSetupGuide

At the end, it pointed to a post regarding setting up a private individual computer server here:

http://www.eqemulator.org/forums/sho...9&postcount=14

I went through each of these steps once, then twice once the first setup failed to connect, and it all was a no-go. Next, I read through the entire thread regarding this specific 2013 install with no luck in all the tips mentioned within. After that all failed, I went to another post and tried to mix-and-match different install ideas from here:

http://www.eqemulator.net/wiki/wikka...rverSetupGuide

When all my tweaks failed, I started over from scratch again. I tried instead a setup I found on the Github site found here:

https://github.com/EQEmu/Server/wiki...up-using-XAMPP

I have gone through this setup twice as well and it still fails to function for me. I am far from a newbie when it comes to computers and have exhausted a week and a half of troubleshooting trying to get this to function. I am sure if I work on it long enough, I can get it, but why frustrate myself if I can get any pointers where something is going awry?

Although one thing that did just come to my mind...due to my schooling, I have the full professional version of Visual Studio 2012 and have been using that to handle my compiling. I have received no errors in my compiling and everything seems to have worked fine. That being said, is there anything in the code which would not compile in 2012 as opposed to 2013? I have coded a lot in both 2010 and 2012, but since I graduated in May have yet to play around with coding in 2013.

[Noport]

Setting up for hosting a private server reference
http://www.eqemulator.org/forums/showthread.php?t=35057

[jimbop]

Originally Posted by Noport

Setting up for hosting a private server reference
http://www.eqemulator.org/forums/showthread.php?t=35057

Thank you also for your input. One of the first things I did after I compiled and went to start up the server for the first time is went into my firewall program to make an exception to open up port 5998 to allow for connections, so I know the firewall currently is not stopping the connection.

[jimbop]

I am still stuck at this spot unfortunately. Does anyone have any ideas for me on how to correct this?

[joligario]

Originally Posted by jimbop

... I checked and double checked again that 5598 is indeed not a typo ...

That is too bad because you should be using and listening on 5998 for Titanium.

Of all the guides you used, I don't know what "no-gos" and "fails" you run into, so I won't even address them. Since I wrote the last guide you linked, I will start there.

2012 vs 2013 doesn't matter. There are very few differences that won't affect your ability to compile this code. Post your errors, post your logs, post your config files, post... anything that can help us help you.

[jimbop]

Originally Posted by joligario

That is too bad because you should be using and listening on 5998 for Titanium.

Of all the guides you used, I don't know what "no-gos" and "fails" you run into, so I won't even address them. Since I wrote the last guide you linked, I will start there.

2012 vs 2013 doesn't matter. There are very few differences that won't affect your ability to compile this code. Post your errors, post your logs, post your config files, post... anything that can help us help you.

Sorry. 5598 was a typo in my post. Lol. It does indeed say 5998 in eqhost.txt like it is supposed to. Here is what I did find, however, when I looked at the logs for my login server:

[Debug] [01.05.14 - 23:18:26] Logging System Init.
[Debug] [01.05.14 - 23:18:26] Config System Init.
[Debug] [01.05.14 - 23:18:26] MySQL Database Init.
[Debug] [01.05.14 - 23:18:26] Encryption Initialize.
[Error] [01.05.14 - 23:18:26] Failed to load EQEmuAuthCrypto from the operating system.
[Error] [01.05.14 - 23:18:26] Encryption Failed to Load.
[Debug] [01.05.14 - 23:18:26] Database System Shutdown.
[Debug] [01.05.14 - 23:18:26] Config System Shutdown.
[Debug] [01.05.14 - 23:18:26] Log System Shutdown.

All of the other logs loaded in like they were supposed to except the one for login, which gave the error stated here. Any help as to how to fix this error? I have EQEmuAuthCrypto.dll sitting in my server folder like it should be, but apparently it does not recognize the file is actually present.

*Edit* As of note, I rechecked that I used the correct x64 bit version needed for my OS and this failed to produce any change in my error.